menu

Welded Mechanical Alloy Steel Tube

Welded Mechanical Alloy Steel Tube, Welded Mechanical Alloy Steel Tube Tolerances, Outside Diameter Tolerance, Inches, Wall Tolerances, As Welded Round Hot Rolled Electric Weld (HREW), Diameter Tolerances, Outside Diameter Size Range Inches, Wall Thickness

Best Quality Steel Pipes !! Genuine Suppliers of Welded Mechanical Alloy Steel Tube, Look Up Quick Results Now!, Better Deal On Bulk Welded Mechanical Alloy Steel Tube, Call us Now & Get Free Estimates!

Welded Mechanical Alloy Steel Tube Dealers India. Welded Mechanical Alloy Steel Tube Dealers Qatar, Welded Mechanical Alloy Steel Tube Dealers Kuwait, Welded Mechanical Alloy Steel Tube Dealers IRAN, Welded Mechanical Alloy Steel Tube Dealers KSA, Welded Mechanical Alloy Steel Tube Dealers Indonesia, Welded Mechanical Alloy Steel Tube Dealers Russia

Alloy Steel Tube

DESIGNATION OF ALLOY STEELS

AISI/SAE Alloy Steels /

HARDNESS CONVERSION TABLE

Approximate Relation of Brinell and Rockwell Hardness to Tensile Strength for Alloy Steel /

HOT ROLLED ROUND ALLOY STEEL

Diameter, Wall & Straightness /

COLD DRAWN ROUND ALLOY STEEL

Diameter, Wall & Straightness /

DOM MECHANICAL ALLOY TUBE TOLERANCES

Cold Drawn Round Welded & Drawn Over Mandrel (Diameter, Wall, Straightness, Ovality) /

WELDED MECHANICAL ALLOY STEEL TUBE TOLERANCES

As-Welded Round Hot Rolled Electric Weld (HREW) (Diameter, Wall, Inside Weld Flash) / As-Welded Round Cold Rolled Electric Weld (CREW) (Diameter, Wall, Inside Weld Flash) /

LOW CARBON ALLOY STEEL PRESSURE TUBE DATA

Heat Exchanger Tube Tolerances / Hydraulic Tube Tolerances / Typical Properties /

ALLOY STEEL TUBE SPECIFICATIONS

SAE/AMS Specifications / ASTM Specifications /

FLUID POWER ALLOY STEEL TUBING

Industry Codes / Industry Specifications (Material, Grade, Class, ASTM, AMS, MIL, Other) / Tube Properties (Material Grade & Class, Tensile PSI, Elong. % in 2”, Hardness) /

SQUARE & RECTANGULAR STRUCTURAL ALLOY STEEL TUBE

Industry Codes / Industry Specifications (Grade, Class, Type, Specifications) / Dimensional Tolerances (OD, Wall Thickness, Corner Radii, Twist, Straightness, Squareness, Flash) / Chemical Composition / Mechanical Properties /

SEAMLESS ALLOY STEEL TUBE

Industry Codes / Industry Specifications (Grade, Class, ASTM, AMS, MIL) / Tube Properties (Material Grade & Temper, Tensile KSI, Yield KSI, Elong. % in 2”, Hard. BHN) /

THEORETICAL BURSTING & BULGING PRESSURES FOR ALLOY STEEL TUBING

CLICK HERE FOR Steel Pipes and Weight, Weight of steel pipes and tubing, ANSI Pipe Chart

Welded Mechanical Alloy Steel Tube Tolerances

As Welded Round Hot Rolled Electric Weld (HREW)

Diameter Tolerances

Outside Diameter Size Range Inches Wall Thickness Outside Diameter Tolerance, Inches
BWG Inches Plus Minus
3/4 to 11/8 incl. l6 to 10 .065 to .134 .0035 .0035
Over 1 1/8 to 2, incl. 16 to 7 .065 to .180 .005 .005
Over 1 1/8 to 2, incl. 6 to 3 .203 to .259 .005 .005
Over 2 to 2 1/2, incl. 16 to 3 .065 to .259 .006 .006
Over 2 1/2 to 3 , incl. 16 to 3 .065 to .259 .008 .008
Over 2 1/2 to 3 , incl. 2 to .320 .284 to .320 .010 .010
Over 3 to 31/2 incl. 16 to 3 .065 to .259 .009 .009
Over 3 to 31/2 incl. 2 to .360 .284 to .360 .012 .012
Over 31/2 to 3 incl. 16 to 3 .065 to .259 .010 .010
Over 31/2 to 4 incl. 2 to .500 .284 to .500 .015 .015
Over 4 to 5, incl. 16 to 3 .065 to .259 .020 .020
Over 4 to 5, incl. 2 to .500 .284 to .500 .020 .020
Over 5 to 6, incl. 16 to 3 .065 to .259 .020 .020
Over 5 to 6, incl. 2 to .500 .284 to .500 .020 .020
Over 6 to 8, incl. 11 to 3 .l20 to .259 .025 .025
Over 6 to 8, incl. 2 to .500 .025 .025 .025
NOTE 1 ó Measurements for diameter are to be taken at least 2 inches from the ends of the tubes.
NOTE 2ó OVALITY shall be within the above tolerances except when the wall thickness is less than 3% of the outside diameter. In such cases the ovality may be 50 percent greater than the outside tolerances but the mean outside diameter shall be within the specified tolerance.

Wall Tolerances

Wall Thickness Outside Diameter, Inches
Inches BWG 3/4 to 1, incl. Over 1 to 115/16, incl. Over 115/16 to 33/4, incl. Over 33/4 to 41/2, incl. Over 41/2 to 8, incl.
Wall Thickness Tolerances, Inches
Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus
.065 16 .005 .009 .004 .010 .003 .011 .002 .012 .002 .012
.072 15 .005 .009 .004 .010 .003 .011 .002 .012 .002 .012
.083 14 .006 .010 .005 .011 .004 .012 .003 .013 .003 .013
.095 13 .006 .010 .005 .011 .004 .012 .003 .013 .003 .013
.109 12 .006 .010 .005 .011 .004 .012 .003 .013 .003 .013
.120 11 .006 .010 .005 .011 .004 .012 .003 .013 .003 .013
.134 10 .006 .010 .005 .011 .004 .012 .003 .013 .003 .013
.148 9 - - .006 .012 .005 .013 .004 .014 .004 .014
.165 8 - - .006 .012 .005 .013 .004 .014 .004 .014
.180 7 - - .006 .012 .005 .013 .004 .014 .004 .014
.203 6 - - - - .007 .015 .006 .016 .005 .017
.220 5 - - - - .007 .015 .006 .016 .005 .017
.238 4 - - - - .012 .020 .011 .021 .010 .022
.259 3 - - - - .013 .021 .012 .022 .011 .023
.284 2 - - - - .014 .022 .013 .023 .012 .024
.300 1 - - - - .015 .023 .014 .024 .013 .025
.320 - - - - - .016 .024 .015 .025 .014 .025
.344 - - - - - .017 .025 .016 .026 .015 .027
.360 - - - - - .017 .025 .016 .026 .015 .027
.375 - - - - - - - .016 .026 .015 .027
.406 - - - - - - - .017 .027 .016 .028
.438 - - - - - - - .017 .027 .016 .028
.469 - - - - - - - - - .016 .028
.500 - - - - - - - - - .016 .028

Inside Weld Flash

HREW tubing is usually produce to OD x Wall dimensions only and in three categories determined by height of inside diameter welding flash:
Flash-In-Tubing ó ID flash does not exceed wall thickness or 3/32" whichever is less.
Flash Controlled .010" ó ID flash is .010" maximum height.
Flash Controlled .005" ó ID flash is .005" maximum height.

As Welded Round Cold Rolled Electric Weld (CREW)

Diameter Tolerances

Outside Diameter Size Range Inches Wall Thickness Outside Diameter Tolerance, Inches
BWG Inches Plus Minus
1/4 to 3/8 incl. 22 to 14 .028 to .083 .0025 .0025
Over 3/8 to 5/8, incl. 22 to 16 .028 to .065 .003 .003
Over 3/8 to 5/8, incl. 14 to 12 .083 to .109 .003 .003
Over 5/8 to 1 1/8, incl. 22 to 14 .028 to .083 .0035 .0035
Over 5/8 to 1 1/8, incl. 13 to 11 .095 to .120 .0035 .0035
Over 1 1/8 to 2, incl. 22 to 14 .028 to .083 .005 .005
Over 1 1/8 to 2, incl. 13 to 9 .095 to .148 .005 .005
Over 2 to 21/2, incl. 20 to 18 .035 to .049 .008 .008
Over 2 to 21/2, incl. l3 to 9 .095 to .148 .006 .006
Over 21/2 to 3 incl. 16 to 9 .065 to .148 .008 .008
Over 3 to 31/2, incl. 20 to 9 .035 to .148 .009 .009
Over 31/2 to 4, incl. 20 to 8 .035 to .165 .010 .010
Over 4 to 5, incl. 16 to 14 .065 to .083 .020 .020
Over 4 to 5, incl. l3 to 8 .095 to .165 .015 .015
Over 5 to 6, incl. l6 to 8 .065 to .165 .020 .020
NOTE 1 ó Measurements for diameter are to be taken at least 2 inches from the ends of the tubes.
NOTE 2ó OVALITY shall be within the above tolerances except when the wall thickness is less than 3% of the outside diameter. In such cases the ovality may be 50 percent greater than the outside tolerances but the mean outside diameter shall be within the specified tolerance.

Wall Tolerances

Wall Thickness Outside Diameter, Inches
Inches BWG 3/8 to 7/8, incl. Over 7/8 to 11/8, incl. Over 17/8 to 33/4, incl. Over 33/4 to 5, incl. Over 5 to 6, incl.
Wall Thickness Tolerances, Inches
Plus Minus Plus Minus Plus Minus Plus Minus Plus Minus
.028 22 .001 .005 .001 .005 - - - - - -
.035 20 .002 .005 .001 .005 .001 .005 - - - -
.049 18 .003 .006 .002 .006 .002 .006 - - - -
.065 16 .005 .007 .004 .007 .004 .007 .004 .007 .004 .007
.083 14 .006 .007 .005 .007 .004 .007 .004 .007 .004 .008
.095 13 .006 .007 .005 .007 .004 .007 .004 .007 .004 .008
.109 12 - - .006 .008 .005 .008 .005 .008 .005 .009
.120 11 - - .007 .008 .006 .008 .005 .008 .005 .009
.134 10 - - .007 .008 .006 .008 .005 .008 .005 .009

Inside Weld Flash

CREW tubing is usually produce to OD x Wall dimensions only and in three categories determined by height of inside diameter welding flash:
Flash-In-Tubing - ID flash does not exceed wall thickness or 3/32" whichever is less.
Flash Controlled .010" - ID flash is .010" maximum height.
Flash Controlled .005" - ID flash is .005" maximum height.

The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values. Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other purposes.


OUR CLIENTS IN Mumbai, Chennai, Bengaluru, Pune, Ahmedabad, Houston, Dubai, Singapore, Hyderabad, Navi Mumbai, Bangkok, Jakarta, Vadodara, Seoul, London, Kuala Lumpur, New Delhi, Abu Dhabi, Tehran, Doha, Madrid, Calgary, Riyadh, Istanbul, Kolkata, Coimbatore, Pimpri-Chinchwad, Dammam, Perth, Busan, Santiago, Noida, Milan, Mexico City, Al Jubail, Sydney, Gurgaon, Sao Paulo, Karachi, Sharjah, Edmonton, Jeddah, Lahore, Melbourne, Ho Chi Minh City, Surabaya, Lagos, Toronto, Bogota, Hong Kong, Kochi, Osaka, Montreal, Cairo, Ajman, Manama, New York, Warsaw, Surat, Buenos Aires, Indore, La Victoria, Chicago, Baku, Ulsan, Tiruchirappalli, Islamabad, Pattaya City, Rio de Janeiro, Chandigarh, Vung Tau, Ankara, Los Angeles, Thane, Medan, Lucknow, Bhopal, Shah Alam, Baton Rouge, Minato, Vasai, Batam, Brisbane, Jaipur, Vancouver, Aberdeen, Faridabad, Yokohama, Monterrey, Dallas, San Antonio, Hanoi, Nashik, Paris, Zagreb, Tel Aviv-Yafo, Quezon City, Bhubaneswar, Mississauga, Alexandria, Kobe, Bucharest, Tunis, New Cairo City, Budapest, Visakhapatnam, San Donato Milanese, Rome, Johor Bahru, Tulsa, Quito, Hamilton, Ciudad del Carmen, Saint Petersburg, Cape Town, Ankleshwar, Vienna, Gimhae-si, Amsterdam, Auckland, Chuo, The Woodlands, Sofia, Seville, Tangerang, Petaling Jaya, Cebu City, Krakow, Gdansk, Sandton, Al Khobar, Adelaide, Berlin, Giza, Mashhad, Genoa, Rotterdam, Makati, Dhahran, Izmir, Phoenix, New Orleans, Belgrade, Laem Chabang, Ras Al-Khaimah, Quebec City, Regina, Prague, Copenhagen, Barcelona, Kuantan, Muntinlupa, Moscow, Washington, Seattle, Milwaukee, Caracas, Tallinn, Minsk, Brno, Frankfurt, Lyon, Birmingham, Sheffield, Cilegon, Patna, Anand, Rajkot, Baghdad, Chiyoda, Colombo, Casablanca, Kota Kinabalu, Lisbon, Kyiv, Pasadena, Kalyan, Stavanger, Vaughan, Essen, Guwahati, Kolhapur, Nagpur, Haifa, Atyrau, Ansan-si, Santiago de Queretaro, Kuching, The Hague, Plock, Port-of-Spain, Cleveland, Portland, Pittsburgh, Austin, Johannesburg, Puchong, Vapi, Ambernath, Thoothukudi, Kaunas, Accra, Pengerang, Oslo Municipality, Rosario, Wednesbury, Bekasi, Rawalpindi, Ploiesti, Denver, Boston, Greenville


SEND ONLINE ENQUIRY


Contact With Us
Email : hitechtubes@outlook.com
(Vinod B Mehta) : +91-98195 80099

Welded Mechanical Alloy Steel Tube, Welded Mechanical Alloy Steel Tube Tolerances, Outside Diameter Tolerance, Inches, Wall Tolerances, As Welded Round Hot Rolled Electric Weld (HREW), Diameter Tolerances, Outside Diameter Size Range Inches, Wall Thickness